XQ89/3Y Tubing Tong is XQ Series well serving tongs. This series power tong used for qucik make-up/break-out in well service opertaions.The tongs is equipped with hydraulic backup tong and use inner curved cam to clamp.
Model XQ89/3Y Hydraulic Power Tongs and spare parts
GB70-85 Inner hex screwM6×16
GB93-87 Spring washer 6
Q3I.1-13A Bearing cover
GB70-85 Inner hex screw M8×20
GB93-87 Spring washer 8
Q3I.1-15A Plate
GB276-82 Ball bearing 6305-RS
Q6C.1-19 Support disc
Q3I.1-10 Clutch big gear
Q3I.1-14 Clutch pinion
Q3I.1-11 Flat key
Q3I.1-9 Spline gear
Q3I.1-8 Inner gear sleeve
Q3I.1-7 Shift gear
GB1152-89 Oil cup M8×1
GB309-77 Roller needleφ3×20
Q3I.1-12 Power input shaft
Q3I.1-2 Housing
GB276-82 Ball bearing 208
Q3I.1-17 Sleeve
Q3I.1-34 Idle shaft
Q6C.1-46 Limit plug
GB70-85 Inner hex screwM6×10
Q3I.1-6 Shaft
Q6C.1-43 Limit plug
Q3I.1-33 Sleeve
Q3I.1-32 Water-proof plate
GB893.1-86 Retainer 62
GB283-87 Short roller bearing 42206E
Q3I.1-31 Sleeve
Q3I.1-30 Idle
Q3I.1-35 Backing plate
Q6C.1-7 Support ring
GB308-84 Steel ballφ5
GB309-84 Cylindrical roller φ8×22
Q3I.1-5 Separator
Q3I.1-4 Cluster gear
Q3I.1.2-2 Shift fork shaft
Q6C.1.2-8 Handle
Q6C.1.2-6 Key
Q3I.1.2-4 Bolt axis
Q3I.1.2-3 Roller
GB6170-86 Nut M6
Q6C.1.2-1 Sliding bearing
Q3I.1.2-1 Shift fork
Q6C.1.2-5 Roller support
Q6C.1.2-4 Roller shaft
GB91-86 Cotter pin2×10
Q6C.1.2-3 Roller
Q6C.1-21 Sliding block
Q6C.1-22 Spring
GB819-85 Cross countersunk srewM5×12
Q6C.1-20 Flat key
GB882-86 Pull pinB20×55
GB91-86 Cotter pin5×30
Q3I.1-16 Back guide rod support
GB70-85 Inner hex screw M12×30
GB93-87 Washer 12 lock
Q3I.1.1-4 Our ring
Q3I.1.1-5 Ramp
GB70-85 Inner hex screw M8×16
Q6C.1.1-14 Spacing screw
Q3I.1.1-3 Jaw plate support
Q3I.1.1-9A Jaw plate
Q3I.1.1-11A Roller
GB71-85 Notched taper screw M8×10
Q3I.1.1-7 Screw plug
Q6C.1.1-13 Spring
Q3I.1.1-6 Insert retaining pin
Q3I.1.1-10 Roller shaft
Q3I.2-17 Die（1）、（3）
Q3I.1.1-2 Upper cover of open gear
Q3I.1.1-1 Cylinder pin
Q6C.1-4 Roller shaft
Q6C.1-5 Roller
Q3I.1-3 Lower support disc
GB70-85 Inner hex screwM5×16
GB892-86 Shaft end ring B25
Q3I.1-19 Upper support disc
Q3I.1-20 Centralizing roller
Q3I.1-21 Shaft-centralizing roller
Q3I.1-24 Tong head cover
Q3I.1-22 Washer
GB71-85 Notched taper screwM6×16
Q3I.1-25 Friction disc
GB93-87 Spring seal 10
GB70-85 Inner hex screwM10×20
GB70-85 Inner hex screw M10×40 with hole in
GB95-85 Base ring 10
Q6C.1-27 Spacing sleeve
GB867-86 Rivetφ2×6
Q3I.1-40 Reset label
Q3I.1-23 Brake plate
GB819-85 Cross countersunk screw M5×8
GB879-86 Spring-type straight pins-slotted5×18
Q6C.1-42 Knob
Q3I.1-41 Reset sleeve
GB70-85 Inner hex screw M6×25
Q3I.1-27 Cover
Q3I.1-29 Brake steel disc
Q6C.1-51 Spring
Q3I.1-26 Connection plate
Q3I.1-28 Reset knob shaft
JB/ZQ4454-86 Copper padφ16×1.5
Q6C.1-24 Oil passing bolt
Model A hose quick joint 10II-520
GB3452.1-82 O sealφ22×3.55
Q3IF2-1 Transient connection plate
XQF2-2 Oil passing bolt
GB3452.1-82 O sealφ45×3.55
GB70-85 Inner hex screw M12×70
GB3452.1-82 O sealφ20×2.65
KZH1-1A Oil returning joint
KZH1-1.1A Oil returning joint
SHD.0 Model H manual reversing overflow
BM3-400 Motor
GB70-85 Inner hex screw M12×40
Q3I.1-18 Operating rod
GB70-85 Inner hex screw M10×40
GB91-86 Cotter pin 4×30
GB882-86 Pin shaft B16×60
GB70-85 Inner hex screw M8×25
Q3I.1-18-1 Hanging support
Q6C.1-45 Back handle
Q3I.1-39 Hole baffle
Q3I.1-38 Product label
Q3I.1-37 Shift label
Q3I.1-36 Insert label
Q6C.1-33 Front handle（left）
Q6C.1-40 Front handle（right）
Q3I.1.3-5 Door shaft（upper）
ZQ3I.1.3-7 Spring shaft（2）
ZQ3I.1.3-5 Jacket
ZQ3I.1.3-6 Spring
ZQ3I.1.3-3 Spring shaft（1）
ZQ3I.1.3-4 Upper shield
ZQ3I.1.3-1 Front shield
Q3I.1.3-4 Door shaft（below）
GB882-86 Pin shaftB20×60
GB91-86 Cotter pin4×26
Q3I.5-7 Plug
Q3I.5-3 Hanging rod
Q3I.5-6 Hanging rod plate
Q3I.5-4 Spring
Q3I.5-8 Label
Q3I.5-5 Cylinder
Q3I.5-2 End cover
GB882-86 Pin shaft B16×55
GB91-86 Cotter pin4×50
Q3I.5-1 Earring
Q3I.4-3 Back guide rod sleeve
Q3I.4-4 Spring
Q6C.4-1A Guide rod pin
Q3I.4-2 Back guide rod
Q3I.4-1 End cover
GB70-85 Inner hex screw M10×30
Q3I.2-23 Barrel cover
GB3452.1-82 O seal φ47.5×3.55
GB70-85 Inner hex screw M6×20
Q3I.2-24 Cover plate
GB3452.1-82 O seal φ33.5×3.55
GB3452.1-82 O seal φ40×2
Q3I.2-11A Gear plunger
Q3I.2-12 Cylinder sleeve
Q3I.2-7 Flat key
Q3I.2-13A Back oil cylinder
Q3I.2-26A Tong tail sleeve
GB/T5780-2000 Bolt M8X65
Q3I.2-9A Cluster gear
Q3I.2-10 Gear cover
Q3I.2-8 Revolution axis
Q3I.2-27 Retaining ring
Q3I.2-6 Backup tong binding clip body
Q3I.2-18 Ramp
Spring(left)
Q3I.2-20 Spring(right)
Q3I.2-21 Jaw plate support shaft pin
Q3I.2-22 Spring separating sleeveφ11×2
Q3I.2-5 Backup tong jaw plate support
Q3I.2-17 Die（1）、（4）
Q3I.2-14 Insert retaining pin
Q6C.1.1-23 Spacing screw
Q3I.2-19 Jaw plate shaft pin
Q3I.2-16 Backup tong jaw plate
Q3I.2-15 Roller
Q3I.2-4 Retaining pin
Q3I.2-3 Knob shaft
Q3I.2-1 Backup tong head cover
GB70-85 Inner hex screw M10×25
Q3I.2-2 Reset knob
Q6C.2-14 Front support of backup tong
Q3I.3-1 End cover
Q3I.3-2 Front guide rod
Q6C.3-1A Guide rod pin
Q3I.3-4 Spring
Q3I.3-3 Front guide rod sleeve
Q3I.1-1 Support of master tong
Q3I.2-2-1 Spring
Q3I.1-42 Retainer
GB/T41-2000 Nut M8
